Cross-Linked Heat Shrinkable Insulation Tape WRSJD

	Product Introduction: Woer Cross Linked Heat Shrinkable insulation Tape (WRSJD) adopts cross-linked polyolenfin and environmental friendly heat melted adhesive -s that can be used for insulation,waterproof and anti-corrosion purposes.
	Characteristics:： 1.Sell shrink rate>30%; 2.Operating temperatute: -55℃ ~ 125℃; 3.Shrink Temperature:100℃.
	Applications: 1.Partial Repair of the cable potective layers  suffered by mechanical and heat damage and erosions and breakages caused by organic  Solvents; 2.Waterproof treatment at the ends of  protective sleevings of heat shrinkable power cable joints; 3.Protection of electriferous naked conductors and treatment of shortcut circuit caused by  icicles; 4.Anti-corrosion and seal of pipes; 5.Insulation of bus bars in switch gear cupboards and power stations; 6.Other areas where insulations and seals are needed.
	Standard color:	Red,Yellow,Green and Black

Technical Data:
Property	Test Method	Stantard
Tensile Strength	ASTM D638	≥12MPa
Elongation	ASTM D638	≥400%
Tensile after Aging	ASTMD 2671/120℃，168h	≥10MPa
Elongation after Aging	ASTMD 2671/120℃，168h	≥350%
Dielectric strength	IEC 243	≥20kV/mm
Volume Resistance	IEC 250	≥1014Ω.cm

Specification:
Size	Standard Width(mm)	Standard Thickness(mm)	Standard Length(m)
WRSJD-0825	25	0.8±0.1	5 or 10
WRSJD-0850	50	0.8±0.1	5 or 10
WRSJD-08100	100	0.8±0.1	5 or 10
WRSJD-1025	25	1.0±0.1	5 or 10
WRSJD-1050	50	1.0±0.1	5 or 10
WRSJD-10100	100	1.0±0.1	5 or 10
Other size are available upon request.

Conductor Splicer   SWT

	Product Introduction: Conductor Splicer is made of non-flame-retardant clear heat shrinkable material,with soldering tin inside.Before using the product, the user has to measure thw outer diameter of the conductor and select size of conducter splicer according to the diameter of the conductor.When the product is used,the two ends of the wire connectors to be joined are inserted into the splicer and joined in the middle.Put the Splicer into a oven for shrinking at a temperature higher than 183℃. Meanwhile,the soldering tin is melted.
	Characteristics: 1.The product starts shrinking at 70℃ and is totally shrunk at 183℃.The soldering tin is also totally meltd at 183℃.The product will be totally shrunk within 3 minutes. 2.The conductor can be firmly earthed without electric welding.It can also effectively relieve the welding stress. 3.Prefabricated soldering tin makes the welding process easily controlled. 4.Unit design makes the nstallation more convenient.
	Standard color:	Clear

Specification:
Size	Size		Conductor O.D.(mm)
	Max.Length(mm)	MIn.I.D.	Min.	Max.
SWT-9001	26	1.7	0.4	1.7
SWT-9002	42	2.7	1.3	2.7
SWT-9003	42	4.5	1.8	4.5
SWT-9004	42	6	2.8	6
SWT-9005	42	7	3.2	7

Page18　Home  Pre. Next  End  PDFdownload

　　Shenzhen Woer Heat-Shrinkable Material Co., Ltd. is the leading manufacturer of heat shrink material products in China. Products we offer are as below: Heat shrinkable tubing, Teflon, PTFE tubing, high heat and abrasion resistant wire, silicone tubing; power cable accessories (heat shrinkable, cold shrinkable and pre-molded for low, medium and high voltage), termination kits, bus bar, insulation sleeves for telecommunication cables and pipeline; fine chemical.